Path: ...!eternal-september.org!feeder3.eternal-september.org!news.dne3.net!.POSTED!not-for-mail
From: Toaster <toaster@dne3.net>
Newsgroups: sci.electronics.design
Subject: Re: 50 ohm termination
Date: Wed, 19 Mar 2025 06:23:25 -0400
Message-ID: <20250319062325.000075e2@dne3.net>
References: <20250317190219.00001b76@dne3.net>
	<6nbhtjlhlpmqkscehm9nn6mfmuvkai55lo@4ax.com>
	<20250317195017.00005882@dne3.net>
	<fglhtjpduk8ivie63rhee5nikakg29vu96@4ax.com>
	<20250318182942.000039a5@dne3.net>
	<v2ujtjl433483f1pehmhmh3f5mk5s5kn49@4ax.com>
	<20250318185944.000070a6@dne3.net>
	<5b9ktjlhumttunmu1c372frpvn7g7uf7om@4ax.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: 7bit
Injection-Info: news.dne3.net;
	logging-data="10960"; mail-complaints-to="abuse@dne3.net"
Bytes: 2595
Lines: 51

On Tue, 18 Mar 2025 19:01:51 -0700
john larkin <jlArbor.com> wrote:

> On Tue, 18 Mar 2025 18:59:44 -0400, Toaster <toaster@dne3.net> wrote:
> 
> >On Tue, 18 Mar 2025 16:02:45 -0700
> >john larkin <jl@glen--canyon.com> wrote:
> >
> >> On Tue, 18 Mar 2025 18:29:42 -0400, Toaster <toaster@dne3.net>
> >> wrote:
> >> 
> >> >On Mon, 17 Mar 2025 19:17:13 -0700
> >> >john larkin <jlArbor.com> wrote:
> >> >
> >> >> On Mon, 17 Mar 2025 19:50:17 -0400, Toaster <toaster@dne3.net>
> >> >> wrote:
> >> >> 
> >> >> >Thank you for the advice. In my case I have a 10Mhz signal with
> >> >> >very sharp transitions (500ps, 5V) and wanted to make sure I
> >> >> >did things properly.
> >> >> 
> >> >> Interesting. What's generating the 5v signal? Lots of AC and
> >> >> Tiny Logic chips are that fast, but might strain to drive 50
> >> >> ohms. We use several tiny triple buffers in parallel sometimes.
> >> >> 
> >> >> Regular thick-film surface-mount resistors are fine as
> >> >> terminators at 500 ps.
> >> >> 
> >> >> LVDS line receivers are great at the receive end.
> >> >> 
> >> >> 
> >> >
> >> >I used a THS3111CD. Split up my project into a timing and driver
> >> >board, so i have some 50 ohm BNC cables between and wanted to be
> >> >extra safe about reflections at these higher frequencies.
> >> 
> >> Is the signal some analog thing, or a 10 MHz clock? The THS is an
> >> opamp, but they can make good cable drivers too, even for clocks.
> >> 
> >> Lately I'm enamored of BUF602, a unity-gain 1 GHz beast.
> >> 
> >
> >I had a really hard time finding a good line driver. I might look
> >into this chip.
> >
> >Thank you!
> 
> Is your signal analog or digital?
> 

digital