Path: ...!eternal-september.org!feeder3.eternal-september.org!news.eternal-september.org!.POSTED!not-for-mail
From: Klaus Vestergaard Kragelund <klauskvik@hotmail.com>
Newsgroups: sci.electronics.design
Subject: Re: nice polyfuse
Date: Sat, 30 Mar 2024 12:14:47 +0100
Organization: A noiseless patient Spider
Lines: 117
Message-ID: <uu8s76$v2q4$1@dont-email.me>
References: <266nvilu01f0mf8n7kgl3rnbdh9ieqqtav@4ax.com>
 <o4gpvi5tppopf5jbbl5r4eti0uvi65rict@4ax.com>
 <s7kpvit2qsj9iq3inntrm8cao41r9b6ar6@4ax.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8; format=flowed
Content-Transfer-Encoding: 7bit
Injection-Date: Sat, 30 Mar 2024 11:14:47 +0100 (CET)
Injection-Info: dont-email.me; posting-host="54d25d8341f3c4674cd3836d0db503ac";
	logging-data="1018692"; mail-complaints-to="abuse@eternal-september.org";	posting-account="U2FsdGVkX18mo15EtrU6vbbRHffOtr3zOJDnVz2fT7M="
User-Agent: Mozilla Thunderbird
Cancel-Lock: sha1:oBHOYdjUxkFhbQcKEvh3JHa8hGU=
Content-Language: en-US
In-Reply-To: <s7kpvit2qsj9iq3inntrm8cao41r9b6ar6@4ax.com>
Bytes: 5492

On 22-03-2024 02:16, John Larkin wrote:
> On Thu, 21 Mar 2024 16:27:13 -0700, boB <boB@K7IQ.com> wrote:
> 
>> On Wed, 20 Mar 2024 19:38:38 -0700, John Larkin <jl@997PotHill.com>
>> wrote:
>>
>>> I've been designing relay-matrix switch modules (how the mighty have
>>> fallen) and I don't want the customers igniting my PC boards or
>>> welding my relays by ignoring our 2 amp max current spec.
>>>
>>> Polyfuses are usually terrible, but this Yageo part is pretty nice.
>>>
>>> https://www.dropbox.com/scl/fi/w7x8rvqgrdua8boqmxg7y/BK60_1-1955033.pdf?rlkey=xpavzb8b8movr2xd4o5amkvx9&dl=0
>>>
>>> https://www.dropbox.com/scl/fi/czk9ids5bj68ytcimcrb5/BK60.jpg?rlkey=77lrxc915it7y083quld9ectb&dl=0
>>>
>>> It (slowly) trips at 2.5 amps in still air at room temp, 3.2 amps with
>>> some air flow. It survived 120 volts DC, which is all I had available
>>> on my bench, pulling about 25 mA.
>>>
>>> The good part is that its cold resistance is only about 0.07 ohms.
>>>
>>> The next question is, if I put it in series with a 1 ohm 5 watt WW
>>> shunt resistor, does the poly protect it from, say, a stiff 60 or so
>>> volt source?
>>>
>>> And does it absolutely protect an inner-layer 50 mil wide 2 oz PCB
>>> trace? I need to do a multilayer board that's 1 oz on the outsides,
>>> for BGAs and stuff, but the board houses don't mind making all the
>>> inner layers 2 oz copper.
>>>
>>>
>>
>> The series power resistor idea is interesting.  Are you wanting to put
>> the PTC in a circuit with voltage above its rating ?
> 
> I plan to spec the instrument for 2 amps and 60 volts max, which is
> the poly rating, but I did verify that the Yageo part survives 120
> volts.
> 
>>
>> If  1 Ohm  5 watts  limits the voltage across the PTC then it's
>> probably good.
>>
> 
> My intent was to have the polyfuse protect the 1 ohm current shunt
> resistor, not the opposite.
> 
> https://www.dropbox.com/scl/fi/7efsvz7ba7wq4ebdxmpcp/P948A4_Shunts.jpg?rlkey=3sw5o5j2uxjnmog4md8lrgisu&raw=1
> 
> 
> I connected the poly and the 1 ohm 5 watt WW in series and then
> connected them to a 60 volt, 5 amp power supply. The resistor smoked
> and then unsoldered itself and survived. The next idea might be to put
> a couple of giant diodes across the resistor. Maybe the poly will blow
> them up too.
> 
> I will have a series relay to engage the 1 ohm shunt, and an ADC
> across the shunt to measure current, so we could software protect it,
> open the relay before the resistor falls off the board.
> 

SW protection is nice, but what happens during power up or when the 
customer only applies power to the relay section, not the unit power. 
Then there's no protection.

What do you need the series resistor for, maybe I missed the point?

> Or an optocoupler across the shunt to sense too much voltage.
> 
> 
>> 0.07 Ohms, cold, is good.
>>
>> We use a 250V 1/2 amp PTC as well as the 1206 size ones.
>>
>> One problem we had with a 1206 15V PTC was that sometimes (rarely) it
>> would burn through and short to the next layer down which was 5V.  A
>> thicker PCB should fix that as well as getting rid of copper just
>> below the PTC on the next layer down.
>>
>> boB
> 
> We found the surfmount polyfuses to be really bad.
> 
> Polys are interesting. Given constant current, at some current they
> begin a slow self-heat thermal runaway and (eventually) go hi-z into a
> basically constant-power mode with surface temp around 100c.
> 
> I think that with a constant voltage drive, they become a sort of
> constant-temperature regulator.
> 
> I did find that if you run them hot for a while, their cold resistance
> goes up, permanently.
> 
> I wish there was a really good 2-terminal current-limiting device. A
> real fuse does that, once.
> 
> The real surface mount fuses are bad too.
> 
> If I want to keep blowing things up, which I do, I need a giant power
> supply. This looks good:
> 
> https://siglentna.com/product/sps5082x/
> 

Looks nice. Now I have to buy one, hoarding instruments you know.

> That ain't cheap, but we can expense it and get basically a 45%
> discount from tax savings.
> 
> The user interface looks typically bizarre.

I have a lot of Siglent stuff.

https://www.electronicsdesign.dk/tmp/Lab2023.jpg

Good instruments, but horrible PC software.